Shimano Road Disc Brake Pads Explained: L05A-RF vs K05S-RX vs L04C-MF
If you ride a Shimano hydraulic disc road or gravel bike, sooner or later you will need new pads, and Shimano's part numbers can look like a code. Three pads cover most current road calipers: the finned resin L05A-RF, the finless resin K05S-RX, and the finned metal L04C-MF. This guide explains what each one is, which calipers they fit and how to replace and bed them in, using Shimano's official product pages and its dealer's manual for the BR-R9270, BR-R8170 and BR-R7170 calipers.
Key Takeaways
- L05A-RF: resin compound with a cooling fin and an alloy back plate. Shimano says it gives less noise and better modulation, plus "long pad life and less fade" from the fin.
- K05S-RX: the same 5th-generation resin compound without a fin, on a stainless back plate. It fits every road and gravel caliper the L05A-RF fits.
- L04C-MF: metal compound with a fin and a composite (alloy and stainless) back plate. Shimano says it gives "more braking power and durability".
- All three fit Shimano's current Dura-Ace, Ultegra and 105 road calipers (BR-R9270, BR-R8170, BR-R7170) and GRX calipers including BR-RX820.
- Replace pads when the most worn part is 0.5 mm thick or if they are contaminated with oil or grease. Bed new pads in with at least 20 stops per brake.
The Three Pads at a Glance
| Pad | Compound | Cooling fin | Back plate | Pad shape | Shimano's description |
|---|---|---|---|---|---|
| BP-L05A-RF | Resin (5th generation) | Yes | Alloy | Narrow type, L | Less noise, better modulation; long pad life and less fade |
| BP-K05S-RX | Resin (5th generation) | No | Stainless | Narrow type, K | Less noise, better modulation |
| BP-L04C-MF | Metal | Yes | Composite (alloy and stainless) | Narrow type, L | More braking power and durability |
All three are designed for 2-piston calipers.

Reading the part numbers
Shimano does not publish an official decoder, but the pattern in its specifications is consistent:
- The first letter (L or K) is the pad shape: L-type pads have a fin-compatible shape; K-type pads are the finless shape.
- The number is the generation (05 is the current resin generation; 04 the metal pad here).
- The letter after the number matches the back plate: A for alloy, S for stainless, C for composite.
- The suffix indicates the compound and fin: R for resin, M for metal, F for fin, X for no fin.
Use this as a guide only, and always check Shimano's compatibility list for your caliper.
Which Calipers Do They Fit?
Shimano lists all three pads for the current road and gravel calipers most riders own:
| Caliper | L05A-RF | K05S-RX | L04C-MF |
|---|---|---|---|
| Dura-Ace BR-R9270 | Yes | Yes | Yes |
| Ultegra BR-R8170 | Yes | Yes | Yes |
| 105 BR-R7170 | Yes | Yes | Yes |
| Previous Dura-Ace / Ultegra / 105 (BR-R9170, R8070, R7070) | Yes | Yes | Yes |
| GRX BR-RX820, RX810, RX410, RX400 | Yes | Yes | Yes |
| BR-RS805, RS505, RS405, RS305 | Yes | Yes | Yes |
| BR-U8010 | Yes | Yes | No |
The differences are on mountain bike calipers: the K05S-RX also fits XTR BR-M9200, M9100 and M9110 but not SLX BR-M7110, while the L05A-RF and L04C-MF fit the XT BR-M8110 and SLX BR-M7110.

K05S-RX is a direct alternative to L05A-RF on road calipers. Shimano lists the K05S-RX for every road and gravel caliper that lists the L05A-RF. The choice is between a finned pad and a finless one.
Resin vs Metal, Fin vs No Fin
Resin (L05A-RF, K05S-RX). Shimano's own summary for its resin pads is "less noise and better modulation". Shimano claims the 5th-generation resin compound wears 50% better than the previous L03A/K03S pads and 110% better than the L02A/K02S generation. For most road riders, resin is the default: quiet, progressive and easy to bed in.
Metal (L04C-MF). Shimano describes metal pads as giving "more braking power and durability". Metal pads are the usual choice for riders who brake hard for long periods, ride heavily loaded or ride in wet, gritty conditions where resin wears faster. They are typically noisier, so expect a little more sound, especially when wet.
Fins (L05A-RF, L04C-MF). Shimano says its radiator fin "provides long pad life and less fade by cooling technology". A finned pad is worth it for long mountain descents, heavier riders and hot climates. Shimano notes that finned pads have left (L) and right (R) markings, so fit them on the correct side.

| If you… | Choose |
|---|---|
| Ride mostly flat or rolling roads | K05S-RX |
| Ride long descents or in heat | L05A-RF |
| Ride heavy, loaded or in wet grit | L04C-MF |
| Want the quietest braking | K05S-RX or L05A-RF (resin) |
Rotors and Pad Compatibility
Shimano's road bikes use Center Lock rotors. Its US store lists the RT-CL700 at $50–$65, the RT-CL800 (Ice Technologies Freeza, with a three-layer stainless–aluminium–stainless construction) at $70–$80, and the RT-CL900 at $95–$110, depending on size.

Some entry-level rotors are sold as resin-pad-only by retailers; the SM-RT10 is a commonly cited example, although Shimano's own product page does not state it. If your rotor is marked "resin pad only", use L05A-RF or K05S-RX, not the metal L04C-MF.
Shimano's dealer's manual also sets rotor limits: do not use a rotor that is 1.5 mm thick or less, or one where the aluminium core has become visible, and never use a cracked or deformed rotor.
When to Replace Your Pads
Shimano's dealer's manual for the BR-R9270, BR-R8170 and BR-R7170 calipers says to replace the pads if:
- they are contaminated with oil or grease;
- the thickness at the most worn part of the pad is 0.5 mm; or
- the brake pad presser spring interferes with the rotor.
Contaminated pads cannot be reliably cleaned, so replace them. Shimano warns not to let oil or grease reach the rotor or pads, and to clean with isopropyl alcohol or a dry cloth rather than commercial brake cleaners on parts exposed to mineral oil.
How to Replace Shimano Road Disc Pads
This summary follows the Shimano dealer's manual. If you are unsure, have a shop do it.
- Remove the wheel and the pad axle retaining clip, then slide out the pad axle.
- Remove the old pads and presser spring.
- Push the pistons back straight with a flat tool. Shimano's procedure uses the oil funnel fitted while doing this.
- Fit the new pads and presser spring, noting the L and R markings on finned pads.
- Refit the pad axle to Shimano's specified torque (the manual gives values for each caliper) and the retaining clip.
- Use the yellow bleed spacer and orange pad spacer as directed during the procedure, then refit the wheel and check the rotor runs freely.
- Pump the lever several times until it feels firm before riding.

Bedding in new pads
Shimano's bed-in procedure:
- Accelerate to a moderate speed on a flat, safe area.
- Operate the brake lever until you slow to walking speed.
- Use one lever at a time.
- Repeat at least 20 times for the front and 20 times for the rear.
Shimano notes that braking force increases during bed-in, and the same applies after replacing rotors. Do not test new brakes on a steep descent.
Troubleshooting Common Disc Brake Problems
Most disc brake complaints come down to a handful of causes. Work through these before buying new parts.
| Symptom | Likely cause | What to do |
|---|---|---|
| Squealing after washing the bike or riding past oily traffic | Contaminated pads or rotor | Replace the pads (Shimano says contaminated pads should be replaced) and clean the rotor with isopropyl alcohol |
| Weak braking with new pads | Pads not bedded in | Follow Shimano's bed-in: at least 20 stops to walking speed per brake |
| Rubbing noise every wheel revolution | Caliper misaligned or rotor slightly bent | Loosen the caliper bolts, centre it on the rotor, retighten; replace a deformed rotor |
| Lever travels further than before | Worn pads or air in the system | Check pad thickness against the 0.5 mm limit; have the brakes bled if pads are fine |
| Grinding or metallic scraping | Pads worn down to the back plate | Stop riding; replace pads and inspect the rotor for damage |
| Rotor feels thin or shows aluminium | Rotor worn out | Replace it; Shimano's limit is 1.5 mm |
Habits that make pads last longer
- Keep lubricants away from the brakes. Apply chain lube with a rag behind the chain, and never spray degreaser or lube near the rotors.
- Clean rotors with isopropyl alcohol only, as Shimano advises, using a clean cloth.
- Brake firmly, not constantly. Long periods of light dragging on descents heat the pads and rotor more than firm braking followed by release.
- Check pad thickness regularly. Shine a light through the caliper from above; once the friction material looks close to the back plate, measure it.
- Carry spare pads on long trips. Pads wear quickly in wet, gritty conditions, especially on long mountain descents.
Upgrading from older pads
If your bike came with older-generation pads such as the L03A or K03S, the 5th-generation L05A-RF and K05S-RX are the natural replacements on current calipers. Shimano claims they wear 50% better than the previous generation. Check your caliper's model number on Shimano's compatibility list before ordering, because older and mountain bike calipers may take a different pad shape.
Frequently Asked Questions
Can I use K05S-RX instead of L05A-RF?
Yes, on road and gravel calipers. Shimano lists the K05S-RX for every road and gravel caliper that lists the L05A-RF. You lose the cooling fin.
Do L05A-RF pads fit 105 R7170?
Yes. Shimano lists the L05A-RF for BR-R7170, as well as BR-R8170 and BR-R9270.
When should I replace Shimano disc pads?
When the most worn part is 0.5 mm thick, if they are contaminated with oil or grease, or if the presser spring touches the rotor.
Are metal pads better than resin?
They are different. Shimano says resin gives less noise and better modulation, metal more braking power and durability. Most road riders are well served by resin.
How do I bed in new Shimano pads?
Brake from a moderate speed to walking speed, one lever at a time, at least 20 times for each brake.
Can I clean oil-contaminated pads?
Shimano says to replace pads contaminated with oil or grease.
How long do Shimano resin pads last?
There is no fixed mileage. Pad life depends on weather, terrain, rider weight and braking style. Shimano only publishes relative claims, such as 50% better wear than the previous resin generation, so check thickness regularly rather than relying on distance.
Do I need fins?
Fins help on long descents, in heat and for heavier riders. For flat or rolling routes, the finless K05S-RX is fine.
Verdict
For most road riders, the L05A-RF is the best all-round Shimano pad: quiet resin, a cooling fin and compatibility with every current road caliper. The K05S-RX is an equally compatible finless alternative for flatter riding. Choose the L04C-MF metal pad if you ride hard in wet, gritty or heavily loaded conditions, and your rotors are not resin-only. Whatever you fit, replace at 0.5 mm and bed the new pads in properly.
Sources
- Shimano product pages: BP-L05A-RF, BP-K05S-RX, BP-L04C-MF
- Shimano dealer's manual DM-RADBR10: replacing the brake pads and safety notes
- Shimano RT-CL800 rotor
Equipment mentioned in this guide
- Shimano L05A-RF disc brake pads
- Shimano K05S-RX disc brake pads
- Shimano L04C-MF metal disc brake pads
Affiliate disclosure: As an Amazon Associate, RydeCruz earns from qualifying purchases, at no extra cost to you. Product availability and prices can change.